- Go to Advanced > Setup > WAN Setup
- Tick Auto WAN Syncing
- Click Apply to save
How do I set up my Netgear telstra?
- Take the bottom cover off the Nighthawk, and remove the battery to view the SIM card slot
- If the micro SIM is not already installed, you’ll find it in the box, in a sealed pouch
- Insert the SIM in the SIM card slot, then replace the battery and the cover
How do I perform a factory reset on my Netgear router
Verify that your router’s Power light is on. On the back of your router, locate the Restore factory settings or Reset button.
Use a paper clip or similar object to press and hold the Restore Factory Settings or Reset button for seven seconds.
Release the Restore Factory Settings or Reset button.
How do I reset my Telstra Netgear modem
Reset your Telstra Smart Modem to factory settings To do this, use a paperclip (or something similar) to press and hold the reset hole at the back of your Telstra Smart Modem, and keep it pressed in for 15 seconds.
Allow 2-5 minutes for the modem to reconnect to the internet.
How do I setup my Telstra gateway modem?
- Step 1 – Connect the nbn connection box, Velocity NTD or Opticomm Optical Network Terminal to your Telstra Smart Modem
- Step 2 – Plug your Telstra Smart Modem into the power outlet
- Step 3 – Connect your devices to the internet
- Step 4 – Connect your home phone (if required)
How do I connect my modem to the internet
Connect the modem power cord into an electrical outlet, then connect the other end to the modem.
Connect one end of one Ethernet cable into the back of the modem, then connect the other end into the Wide Area Network (WAN) port on the router.
How do I activate my modem
Plug your modem’s power cord into an electrical outlet. Enter your modem’s 12-digit MAC number.
Once your modem is connected to the coax cable in an active outlet and the power cord plugged into an electrical outlet, you’ll be prompted to Check Your Connection.
How do I connect my Telstra smart modem to my NBN box?
- Plug the nbn connection box into a cable port
- Plug the nbn connection box into the power outlet
- Connect the nbn connection box to your Telstra Smart Modem
- Plug your Telstra Smart Modem into a power outlet
How do I connect my Telstra gateway modem?
- step 1 – connect to your modem via Wi-Fi or Ethernet
- step 2 – log into your modem
- step 3 – enter the MATE settings into your modem
- step 4 – plug your modem into your telephone wall socket
How do I install Telstra Smart modem Gen 2?
- step 1 – connect to your modem via Wi-Fi or Ethernet
- step 2 – log into your modem
- step 3 – enter the MATE settings into your modem
- step 4 – plug your modem into the nbn™ device
How do I access my modem settings
What to Know. Connect your computer to your modem with an Ethernet cable, open a browser and enter your modem’s IP address in the URL bar.
The default user name (sometimes listed as SSID) and password are typically printed on the bottom of the modem.
How do I access my Telstra modem
Option 1: Find your Telstra modem’s default address Enter the correct URL for your modem: For nbn™/ADSL/Velocity/Cable (with Adapter) modems – enter http://10.0.0.138 or http://telstra.gateway/ For Cable (without Adapter) modems – enter http://192.166.0.1 or http://telstra.gateway/
How do I put my Telstra smart modem in bridge mode
In the Telstra modem admin GUI at 192.168. 0.1 , Go To Advanced -> Internet -> WAN Services -> Toggle ‘bridge enabled’ to off.
Confirm and wait for the progress bar and for the modem to reboot.
How do I check my modem?
- Launch a web browser from a computer or mobile device that is connected to your network
- Enter your cable modem or modem router’s user name and password
- Select Cable Connection
How do I move my NBN modem to another room
Your Smart Modem is connected via an ethernet cable to the nbn co network termination device.
A registered cabler can connect a LAN outlet on the wall of another room to relocate your Smart Modem.
To connect to an existing or new phone socket in another room, you will need a registered cabler.
Can I use my own router with nbn
In this case, you will simply need an eWAN (Ethernet Wide-Area-Network) Wifi router (there is no need for a modem component).
You can supply and connect your own hardware as long as it isn’t locked to your current or previous internet service provider, and that it is nbn™ compliant.
How do I update my Telstra modem
Manual firmware updates are not available on the Telstra Smart Modem, these will be automatically updated when they become available.
Updates are pushed out between the hours of midnight and 6:00am. You’ll simply need to have your modem connected during these times for the updates to download and take effect.
Can I use my own router with Telstra NBN
As you’re probably aware, not all ADSL routers can work on the NBN. So if you’re using your own router that wasn’t purchased as part of your Telstra Business Broadband on the NBN service, please refer to the equipment manufacturer’s guide or seek assistance from a qualified network specialist.
What type of Telstra modem do I have
You can also check your Telstra Smart Modem model number by entering http://192.168.0.1/ in your browser and signing in.
The username is admin and the default password is Telstra for Telstra Smart Modem 1.1 and Gen 2.
How do I test my Telstra modem
In a browser, go to ‘speedtest.telstra.com’ to perform a speed test.
What lights should be on my modem
The power light, downstream indicator, upstream indicator, online indicator, and link light on your modem should all be green.
If your power light is yellow, it may be upgrading, so leave the modem on and give it a little time to do its thing.
How do I pair Telstra Smart modem Gen 2?
- On your device, go to ‘Settings’ and then ‘Wi-Fi’
- On your Telstra-supplied modem, press and hold the ‘Pair’ or ‘WPS’ button for up to 5 seconds
- When the ‘Pair/WPS’ light flashes, your device is connected to the Wi-Fi
How do I unlock my Telstra smart modem
Head over to Telstra’s Bill Pay web page and make the required unlock fee payment, and be sure to take note of your receipt number.
Give the Telstra Unlock team representative the receipt number, and take note of the unlock code they give you.
Is the NBN connection box a modem
As an NBN modem, the NBN connection box needs power to operate, plus it also needs an Ethernet connection to a router or modem-router (in ‘bridge’ mode, aka ‘router’ mode) to share the NBN connection with devices around your home.
What does NBN modem plug into
Your NBN™ Connection Box will plug into the same wall socket that you previously used for traditional copper phone handsets and/or ADSL broadband.
You can connect your iiNet modem to your NBN™ Connection Box to set up your home WiFi network.
How long does it take to set up a Telstra modem
To set up your new Telstra Smart Modem by connection type, you can download the set-up guide or follow our step-by-step instructions below.
Installation will take up to 30 minutes.
Where is the WPS button on Telstra gateway modem
On your Telstra-supplied modem, press and hold the ‘Pair’ or ‘WPS’ button for up to 5 seconds.
Depending on the type of modem you have this will either be on the front or back of the device.
Do you need to use Telstra modem for NBN
If you’re connecting to the nbn network with us on an eligible plan, you won’t have to pay for a standard Telstra-supplied modem.
This will be advised during your connection order. Good to know: You can choose to supply your own modem, but that would be at your expense.
Why is my internet not working Telstra
If your broadband isn’t working, it might be because of an outage on the nbn network, on the Telstra network in your area, or due to maintenance.
Check if there’s an outage in your neighbourhood on Telstra Outages.
Do I have to use Telstra modem for NBN
Fibre to the Building NBN: You’ll need a modem router. This will plug into the telephone socket used to facilitate your NBN connection.
Fibre to the Curb NBN: You’ll need a router. This will plug into the NBN Connection Box supplied by NBN Co for free.
Why would you need Wi-Fi 6
WiFi 6 increases the number of streams to a new high of 12 across the 2.4 and 5 GHz bands, whereas WiFi 5 has a limit of 8 in a dual band configuration.
This increase of streams provides higher connection speed, and your client devices have more paths to communicate with your WiFi router.
Sources
https://smallbusiness.chron.com/modem-work-internet-provider-60353.html
https://www.jabra.com/blog/dect-vs-bluetooth-how-to-choose-right-wireless-headset/
https://support.itsolver.net/hc/en-au/articles/360001206036-What-do-the-lights-on-your-Telstra-Smart-Modem-Gen-2-mean-
https://www.telstra.com.au/support/category/broadband/manage/adsl2-plus-compatible-modems-and-in-line-adsl-filters
